getting my SE6 back on the road bulld/progress thread.
- ClubCalibra.net
- Posts: 144
- Joined: Tue Mar 10, 2015 10:38 pm
Re: getting my SE6 back on the road bulld/progress thread.
Hi all....I`m still here....
Sorry not been on here for awhile..been painting the block and any bits i can take off....new gaskets when ever needed..
![Image](https://s20.postimg.org/sy6qhob31/my8v4.jpg)
![Image](https://s20.postimg.org/smpa4wun1/my8v5.jpg)
![Image](https://s20.postimg.org/pyztuk1lp/my_C20_NE.jpg)
3/8/2017.....managed a few hours on the Calibra today...not been down for three weeks due to commitments etc.....managed to get the Crank Sprocket off today as there was a bolt sheared off in it....now I`ve seen scary videos on youtube about the Crank bolt and using a breaker bar and turning the engine over to crack it lose....no way was i going to try that....I have a 12v Inpact Wrench I got a few Christmas`s ago...so i thought i would try that....OMG it worked !!! I held the sprocket by hand and buzzed it off in two attempts...now i know the Cam belt was done about 10k ago so maybe they had it off then.....
https://www.youtube.com/watch?v=tbAcz-jBp24
So cleaned up the side again and painted it again in VHT paint...
![Image](https://s26.postimg.org/ubvx0vu2h/engine_Side.jpg)
![Image](https://s26.postimg.org/mpnjpqmm1/Crank_Sprocket_1.jpg)
![Image](https://s26.postimg.org/e8o1ethx5/Crank_Sprocket_2.jpg)
Not bad for just over an hours work....be beck soon
![Axed :axed:](./images/smilies/axed.gif)
![Image](https://s20.postimg.org/sy6qhob31/my8v4.jpg)
![Image](https://s20.postimg.org/smpa4wun1/my8v5.jpg)
![Image](https://s20.postimg.org/pyztuk1lp/my_C20_NE.jpg)
3/8/2017.....managed a few hours on the Calibra today...not been down for three weeks due to commitments etc.....managed to get the Crank Sprocket off today as there was a bolt sheared off in it....now I`ve seen scary videos on youtube about the Crank bolt and using a breaker bar and turning the engine over to crack it lose....no way was i going to try that....I have a 12v Inpact Wrench I got a few Christmas`s ago...so i thought i would try that....OMG it worked !!! I held the sprocket by hand and buzzed it off in two attempts...now i know the Cam belt was done about 10k ago so maybe they had it off then.....
https://www.youtube.com/watch?v=tbAcz-jBp24
So cleaned up the side again and painted it again in VHT paint...
![Image](https://s26.postimg.org/ubvx0vu2h/engine_Side.jpg)
![Image](https://s26.postimg.org/mpnjpqmm1/Crank_Sprocket_1.jpg)
![Image](https://s26.postimg.org/e8o1ethx5/Crank_Sprocket_2.jpg)
Not bad for just over an hours work....be beck soon
- ClubCalibra.net
- Posts: 144
- Joined: Tue Mar 10, 2015 10:38 pm
Re: getting my SE6 back on the road bulld/progress thread.
Looking good Mark!
Re: getting my SE6 back on the road bulld/progress thread.
Cliff wrote:Looking good Mark!
Thank you mate....pity about Photobucket stopping free third party hosting though....!
- ClubCalibra.net
- Posts: 144
- Joined: Tue Mar 10, 2015 10:38 pm
Who is online
Users browsing this forum: No registered users and 184 guests